Hello everyone, in this video I will will walk you through the capture workflow showcasing how SBA and IP stream interest are managed between IMAM and MOOG technologies.
So we start with the storage configuration.
Inside the MOG interface you go to the setup and storage.
Both IMAM and MOC systems should have access to the storage typically configured as Sif's SMB, although more can also.
What about various types of storage including S3?
For this specific configuration we need the disk based storage accessible by both the systems.
So that is SMP, SIPS and.
Here there is a storage IP address and the user ID password to connect to the storage and then there is a base path configuration and so we are creating the original proxy.
The XML watch folders and everything has subfolders under this base path.
So once the storage is configured, the next step is to configure the asset management.
For that you can go back to the set setup and then there is a asset management section.
Here we use the XML option with the EMA as the destination storage.
That is the asset management configuration.
The next is the locators.
The locators are available from setup and Locators.
Locators are shortcuts to tag the clip while it is recording which is helpful for building your logging workflow.
Here I have a look locator profile called Logging and with a few actions code we can keep on adding new code and label it here.
OK, let's move on to the input configurations.
With the input out, put tap.
There are various options to configure the streams input and HDI HDMI IP.
So we did more.
You can configure various input streams such as NDA, RTP, RT, SPSRTUDP and so on.
Then additionally SDA capture configurations can be managed.
So for that you have to go to here and there is an SDA configurations are here.
So you have to select the capture type, capture interface, then the capture card.
There are various options like Decklink, Go Fish, Petrox and and signal generator.
In this case it's a deck link and then I do have few more created here.
So this is I'm using a signal generator to just to generate A24P signal and 30 P signal for the testing purpose.
The next step is to create the the metadata profiles.
For that you have to go to the workflows and there is a metadata profiles option inside the workflows.
Here you can define the system metadata and custom metadata fields.
You can use the metadata standard ID from Emap to map the fields between MOG and Emap.
In this case I have two custom metadata fields.
So these are the standard ID coming from Emap and these are the system fields.
We can mention it as ignore and if you are defining the custom metadata, you have to select the option ask to user.
Also you can change the type and also ensure that these available naming template options are checked.
Let me just go ahead and create a metadata field.
Go to the admin tools manage metadata.
I am just going to create a field called House number and click on Add.
So in this case I have a cust field house #5 going to select that and going to name the field and this is the friendly name.
I can just take it as house number and then I am going to select ask to user and available in the naming template.
So that is how you can define the custom metadata fields in MOG and map it to the fields in e-mail.
So once you click on save you can move to the naming template.
So the naming template.
So here I am selecting the metadata profile that is created in the previous step and all system fields are here.
The custom metadata fields here and also the separators are available.
This is used to create the destination naming.
In this case I am using the original source name that is the the system field.
The_is the separator here then.
I AM putting a 01_ and I believe THE a a a is the unique number or if.
I need TO add something I can JUST put another dash here and put a label here and so on and so on so I'm.
Just Going to stick to the current naming template then ensure.
That the append_P to the proxy Clip names option is selected this.
Option is only applicable for the capture workflow the.
Capture workflow will not work if this option is not selected and.
Also if this option is selected for the file based transcode workflow that also won't work so.
Ensure that this is selected only for the capture workflows the.
Next is the workflow profile.
So for that you have to go to the workflows and go to the workflow profiles.
The various types of workflow can be code figured here.
But I am going to stick to the capture workflow.
So in this case the output the operation is record.
So there are various other options are there for the this specific capture workflow.
The option we have to select is Record and the standard mode is available and Format family.
This is all customer choice.
In this case it's Apple Pro and then you can select Apple Prores 422 or 444 or HQ format.
This again depends on the customer requirement.
Then the wrapper can be selected here.
Here I am selecting the OP 1A SEMD as the wrapper and then destination is the IMAP storage and the base path is Flash MOG XML and they give base path is configured in the setup and then taking a subfolder there for the base path.
Similar configuration is for the proxy.
In this case we need AH 264 proxy and the format is.
I am selecting A480P proxy and the destination wrapper is MP4 and the storage is enough and that file also going to the same location.
Then in the clip naming select that aiming template we created so that is to include original name_01_the sequence number all other.
Fields are also here.
See that the house number which I created THAT is available here.
I need to make changes.
I have to go back to the naming template and do the edit and then this is the place you can review the metadata.
And again, if I just need to make changes in the metadata profile, I have to go back the metadata profile and make the changes there.
So all the three fields are available.
Then the asset management I had to select the the target as XML and then using the option XML to e-mail.
And that also pointed to the the same folder location.
Yeah, that is the old configuration required for the capture workflow.
Then let me go to the dashboard and let me maybe go to the crash record.
So the options are available here to change the input to test to 24 PE or at Chandas or whatever the the input.
What are the inputs configured?
Those things are available here to select it and I'm going to stick to the HLS one input here.
And so this is the the custom metadata fields which I created Deborah coding title again, this is a custom metadata fields, the house number maybe I will put it as H101 and then I can click on record.
So while the recording is progressing, I can click on these locators.
And again there is a option to change the template here.
Now I have only one I'm selecting that and I'm selecting layer HLS 1 here.
And then if I click on South new located is added.
And yeah, I can keep on clicking on these buttons if the if it is labeled and colour coded with the labels.
So there can be different buttons created part of the locator profile.
Once they recording is completed you can click on stop and again there is a multi viewer available.
Multiple crashed recording is available, scheduled recording is available.
So that is all.
I leave it to the the MOG documentation and everything or MOG videos to learn about that.
I'm just going to click on stop here and the recording is now stopped.
So now if I go back to the Imam system and now XML is created, this is the Imam site car XML.
So this is to process that media.
So what is happening behind the scenes?
The configurations we have done at the workflow profile level?
The original file, proxy file and also the asset management XML file going to the same location.
And then we have added the Moog XML processing module to the IMAD XML watcher.
It takes XML arse it extract all the information and it will create a EMA car XML and then hand over that to the the Eva we just manager.
So that is all activities are happening behind the scenes and once the process is completed that is the file which I just recorded and here is the preview and these are the the locators which I added while recording and in the metadata.
So those are the the comments and title metadata that is also added.
One thing I missed is I have to add the house number also to the metadata group once that is completed.
So that is house number and all those informations are directly coming from the MOC interface.
That's all.
Thanks for watching.